商品描述價格說明聯系我們規格25KG/包mm加工定制否特性玻纖增強;阻燃材質PET顏色本色中文名稱聚對苯二甲酸乙二醇酯銷售方式品牌經銷用途電氣 家電 汽車廠商美國杜邦牌號FR330加工方式注塑成型應用開關應用廠地美國經銷方式品牌銷售FR530聚對苯二甲酸乙二醇酯#聚酯|PET美國杜邦填充物:玻纖增強物性信息：基本性能額定值單位測試方法吸水率0.05%ASTM D-570物理性能額定值單位測試方法模具收縮率 (3.2mm,flow)0.25% (1.57mm.flow)0.16%比重1.67ASTM D-792機械性能額定值單位測試方法IZOD沖擊強度 (-40℃)80J/mASTM D-256彎曲強度 (23℃)200MPaASTM D-790IZOD沖擊強度 (23℃)91J/mASTM D-256無缺口沖擊強度 (23℃)585J/mASTM D-4812IZOD無缺口沖擊強度 (-40℃)535J/mASTM D-4812電氣性能額定值單位測試方法介電常數ASTM D-150 (10)3.7 (10)3.8介電強度 (1.6mm)25.0kv/mmASTM D-149體積電阻率10Ω.cmASTM D-257抗電弧性60-120SASTM D-495介電強度 (3.2mm)18.0kv/mmASTM D-149表面電阻率10ΩASTM D-257損耗因數ASTM D-150 (10)0.018 (10)0.011CTI250-400VUL 746A熱性能額定值單位測試方法熱變形溫度ASTM D-648 (0.45MPa)246℃ (1.80MPa)224℃Characteristics of DuPont PET plastic raw materials in the United States:PET is a milky white or pre yellow highly crystalline polymer with a smooth and shiny surface. Creep resistance, fatigue resistance, wear resistance, and dimensional stability are good, with low wear and high hardness. It has the greatest toughness among thermoplastic materials: good electrical insulation performance, less affected by temperature, but poor corona resistance. Non toxic, weather resistant, stable against chemicals, low water absorption, resistant to weak acids and organic solvents, but not resistant to hot water immersion or alkali.PET resin has a high glass transition temperature, slow crystallization rate, long molding cycle, long molding cycle, high molding shrinkage rate, poor dimensional stability, brittle crystallization molding, and low heat resistance.Through the improvement of nucleating agents, crystallization agents, and glass fiber reinforcement, PET not only possesses the properties of PBT, but also has the following characteristics.1. The thermal deformation temperature and long-term use temperature are the highest among thermoplastic general engineering plastics2. Due to its high heat resistance, reinforced PET is immersed in a soldering bath at 250 ℃ for 10 seconds without deformation or discoloration, making it particularly suitable for preparing electronic and electrical parts for soldering:3. The bending strength is 200MPa, the elastic modulus reaches 4000MPa, and the creep and fatigue resistance are also good. The surface hardness is high, and the mechanical properties are similar to those of thermosetting plastics.4. Due to the fact that ethylene glycol used in the production of PET is almost half cheaper than butanediol used in the production of PBT, PET resin and reinforced PET are the lowest priced engineering plastics with high cost-effectiveness
